 |  |  |  |  |  |  |  |  |
 |
|  |
04-02-2008, 03:35 AM
| ||||
| ||||
| Cannot shoot over 250 I am having trouble with my A-5 with a Dead On power tube. Dialed all the way in and brought all the way out, I cannot get my gun to shoot more than 250 fps. I have adjusted springs, replaced springs, nothing. What could the problem be  |
|
04-02-2008, 03:53 AM
| ||||
| ||||
| Re: Cannot shoot over 250 What air source are you using? What is your total setup? IF using a regulator, what pressure is it reading? Have you replaced the drive spring?
__________________ JackRock  Whether helping my team take a hill, a new player with equipment failure, or helping you to the dead zone. I hear the call to service and I answer: I am an Operator. Check out my paintball YouTube Videos. |
|
04-02-2008, 04:58 AM
| ||||
| ||||
| Re: Cannot shoot over 250 Total setup is A5, Dead on PT, regular and egrip. Nothing special. Yes I have replaced the spring. -Lee |
|
04-02-2008, 06:58 AM
| ||||
| ||||
| Re: Cannot shoot over 250 Welcome to A5OG! Did the problems start when you installed the new powertube? Did it do this before? Are you using HPA or CO2? I had the same issue with my A5. It can be the older style rear bolt and valve. I called Tippmann and they replaced mine with the new style X7 rear bolt and valve. It has to do with the way the valve is made. There is some different milling to the new valve. If I used CO2, I was OK but when I used HPA, I had the low velocity issue.
__________________ You must be the change you want to see in the world ~ Gandhi Before voting watch this-Link #1 & Link #2! |
|
04-02-2008, 08:16 AM
| ||||
| ||||
| Re: Cannot shoot over 250 Most likely will be the valve. This is the old style valve  This is the new style x-7 valve  Call them and see if they send you a new one or purchase it from tippmannparts.com |
|
04-02-2008, 10:53 AM
| ||||
| ||||
| Re: Cannot shoot over 250 Awesome, I'll call them up and see what they say about getting one out. BTW I am running CO2. |
|
04-02-2008, 11:46 AM
| ||||
| ||||
| Re: Cannot shoot over 250 Well, it's still a little cold in some places. If that applies to you then cold CO2 loses a lot of pressure. And just for some clarification, how exactly did you replace the drive spring? Did you just go for a straight stock spring swap or did you use a spring kit? Also do you have a buttstock or other non-stock end plate? Sometimes those have a deeper spring hole and you lose some tension from it.
__________________ You can't wipe a welt -J Paintball FAQ's | Asking yourself "What should I get next?" | Paint & Barrel Facts | Fixing the Chop HPA vs. CO2 | Regulator FAQ's | To Remote or Not To Remote | Slide Checks 101 | LPK FAQ's Complete A-5 Maintenance | Complete T-8 Maintenance | Which Vest is for Me? | Secondary Sights | Rails, Sights, & Targeting Sale - Custom Vests, MOLLE Gear, Dogleg Stock, & More |
|
04-02-2008, 11:51 AM
| ||||
| ||||
| Re: Cannot shoot over 250 Stock springs and I have an opsgear folding AK stock |
|
04-02-2008, 11:51 AM
| ||||
| ||||
| Re: Cannot shoot over 250 Receivers could be torqued down to by the bolts. turn the bolts by like 10 degrees counter-clockwise. How cold is it where you are playing? As asked before, did the issue only arise after the install of the powertube?
__________________ SilentDeath12886's Compilation of A-5 Projects  http://www.a5og.net/5-photo-gallery/...tml#post125307The E-bolted A-5  http://www.a5og.net/5-mods-upgrades/...tml#post108414The X7 egrip retrofitted A-5  http://www.a5og.net/5-mods-upgrades/...tml#post122941The old A-5  http://www.a5og.net/showthread.php?t=5009The 98c backup  http://www.a5og.net/showthread.php?t=5893 |
|
04-02-2008, 12:08 PM
| ||||
| ||||
| Re: Cannot shoot over 250 It's possible the stock has a spring hole that's too deep. Try placing a BB in it to take up some slack of the drive spring.
__________________ You can't wipe a welt -J Paintball FAQ's | Asking yourself "What should I get next?" | Paint & Barrel Facts | Fixing the Chop HPA vs. CO2 | Regulator FAQ's | To Remote or Not To Remote | Slide Checks 101 | LPK FAQ's Complete A-5 Maintenance | Complete T-8 Maintenance | Which Vest is for Me? | Secondary Sights | Rails, Sights, & Targeting Sale - Custom Vests, MOLLE Gear, Dogleg Stock, & More |
 |
« Previous Thread
|
Next Thread »
| Thread Tools | |
| Display Modes | |
Linear Mode
| |
All times are GMT -4. The time now is 07:45 AM.
